CATEGORY LISTINGS > MAINTENANCE / SERVICE

Replying to Thread:

injection pump issues

Created On Saturday 27, November, 2010 10:47 PM by Lawnranger

Please enter your login information to post.
Username:
Password:
I want to stay logged in.

Message Title:

Message Text:

http

https

ftp

mail

hr

highlight

LI Quote

HTML code is not permitted. Special symbols permit some HTML functionality.

Lawnranger

Posts: 1
Joined: Nov 2010

Saturday November 27, 2010 22:47

Hi! I have a gmc/isuzu 1990 4bd1t diesel. Idrained the fuel seperator & slimy gel came out .I then changed the fuel filter.Primed the system started the truck,bled the air out of lines.Truck ran good for about 15min.Then acted as if it ran out of gas.Repeatedly primed fuel & bled.same results.Had someone inform me that there was a sreen in the fuel line before the primepump.Cleaned,primed & bled same results.Thanks for any advice.

-------------------------
andyoconnor

Quote

Top

Bottom

maran

Posts: 3
Joined: Nov 2011

Tuesday November 15, 2011 01:54
Well, most of the information you find online are the manufacturers or suppliers of such systems, so most of them are very biased. You can inject any kind of fuel in a diesel engine through the intake, you can buy alcohol injection systems, diesel and LP gas/propane. They are all basically the same design and workings. ------------------------- Zirconium Pump

Quote

Top

Bottom

WilliamFritz

Posts: 5
Joined: Nov 2011

Friday November 18, 2011 00:15
With a branded and reliable pump such as a Laing pump, the number of problems and outages will be minimal. The insulin pump involves a lot of maintenance issues such as change of batteries, infusion sets, insulin vials, etc to prevent the onset of infection at the site of insertion. ------------------------- Atlanta Electrician

Quote

Top

Bottom

KyleAdam

Posts: 13
Joined: Dec 2011

Thursday January 12, 2012 03:09
Pumps deliver insulin in one of two ways. One, is continuous, which is referred to as the basal rate.The Bosch injection pumps are basically devices that are used for pumping fuel into cylinders of an engine, mostly, a diesel engine or a gasoline one. ------------------------- Conductor Repair Kit

Quote

Top

Bottom

alexisrois

Posts: 26
Joined: Feb 2012

Wednesday August 29, 2012 09:40

The best way to start this explanation is to quote an e-mail that I found on the corporate Cummins website many years ago. “The Bosch VP44 has not been as reliable as we had hoped”. We have dismantled many pumps to figure them out and diagnose what failed and what the cause AND SOLUTION is for the failure. We think you might like to hear about our findings.

-------------------------
Fire Pump Systems provide a wide range of fire pump from Ruhrpumpen

Quote

Top

Bottom

DieselD

Posts: 1
Joined: Oct 2014

Wednesday October 08, 2014 06:41

If that's a VE type pump then two things could be going wrong. #

1) There is air still sucking in and causing the pump to lose pressure. Low pressure will cause hard delivery.
2) Inside the pump is a section called the transfer pump. This actually sucks the fuel from the tank into the pump. It creates pressure inside the pump and enables injection. If the transfer pump has dirt it may cause it to jam and result in a low amount of fuel being pumped from the tank.

Since your filter had loads of dirt you may find dirt or contaminated fuel has entered into the pump. It needs to be serviced and calibrated with new seals and gaskets. Any leaks would allow air to suck into the pump causing similar problems to what you've exlained.

After serviving the pump, have the tank drained and cleaned to remove any contaminated fuel that will quickly block up the filters. Also ensure there is a water trap and it never overflows. Water will damage fuel injection parts rapidly. The injector pressure should also be reset and nozzles replaced if they are pitted.

-------------------------
Cat, Cummins, Detroit, Volvo Diesel Injection Aftermarket Parts.

Quote

Top

Bottom

[ CATEGORY LISTINGS : THREADS ]

SELECT Advert_Number, Size_Type, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type = 2 ORDER BY Advert_Number

SELECT Imps_Available FROM Advert_Imp WHERE Advert_Number = UPDATE Advert_Imp SET Imps_Available = #Imps_Available1# WHERE Advert_Number = SELECT Impressions FROM Advert_Imp_Trans WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# UPDATE Advert_Imp_Trans SET Impressions = #Impressions1# WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# INSERT INTO Advert_Imp_Trans (Advert_Number, Date, Impressions, Clicks) VALUES (#Advert_Number#, #CurrentNow#, 1, 0)

SELECT Advert_Number, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type=1 ORDER BY NEWID()

Customer Testimonials

'We sold a Deutz 6 cylinder to a new customer in Illinois within weeks of listing! Because the customer contacted us directly from the start, the deal went very smoothly.'

Leon Weller, Diesel Power Supply Co, Texas, USA

'I had a Cummins ISX600 sitting in my shop for 2 years and finally managed to sell it through DieselEngineTrader.com! Great service and I like the way that the Buyer was able to phone me directly.'

David G Bouchard, Los Angeles, USA

'Urgently needed a diesel engine for a generator set. Found one that suited on DieselEngineTrader. It is very easy to find what you are looking for!'

Trond Paulsen, Norwegian Maritime Equipment A/S

injection pump issues

Customer Testimonials

Newsletter