Replying to Thread:

hot restart for 6.5td

Created On Monday 13, September, 2004 12:38 PM by capt4

Please enter your login information to post.
Username:
Password:
I want to stay logged in.

Message Title:

Message Text:

http

https

ftp

mail

hr

highlight

LI Quote

[q]oh i forgot, no codes or other factors.. i did try something, when it was acting up i poured some cool water on the pmd and whamo!! it fired right up. i am thinking PMD more and more..[/q]

HTML code is not permitted. Special symbols permit some HTML functionality.

capt4

Posts: 3
Joined: Sep 2004

Monday September 13, 2004 12:38

Hi-

I have a 96 6.5td that runs great, sounds like I have the only one in existance. the issue i have is hot restarts after an extended soak 15-90 minutes. I have found a service bulliten that says i need to let the engine idle for 5-10 minutes then shut it down. the cause they say is that the fuel viscosity is too low after the soak to create enough pressure to "pop" the injectors- makes sense. this is a real pain in the butt. does anyone know if there is another fix or some aftermarket something that cures this. about the only thing i have had some mixed success with is useing a lot of fuel addative. it is not the PMD i have one on the pump and one remote and both have the same issue of the hot restart-long crank....

Thanks!!

Quote

Top

Bottom

fozsey

Posts: 23
Joined: Sep 2003

Tuesday September 14, 2004 10:53
Unfortunatelly, hot restart issues point to the IP itself most of the time unless there is another contributing factor. How many miles do you have on your pump? Any other issues, i.e. codes, etc?

Quote

Top

Bottom

capt4

Posts: 3
Joined: Sep 2004

Thursday September 16, 2004 12:34

it is a rebuild pump and has maybe 30k on it. i would hate to think that i spent $1000 for a rebuild pump and it is going bad already. i think i am going to try another PMD. when i used the pmd on the pump, it would occaasionally do this. like after driving all night @80mph.. so I remoted mounted a new PMD and have not had any problems this summer, well until now. without fail if the truck soaks for 15-90 minutes it is a real bear to start. like a 20 second or so crank. after it cools off it takes maybe .5 second crank to start it.... i am just stumped on this-esp after reading the GM service bulliten ....

Quote

Top

Bottom

capt4

Posts: 3
Joined: Sep 2004

Thursday September 16, 2004 12:36
oh i forgot, no codes or other factors.. i did try something, when it was acting up i poured some cool water on the pmd and whamo!! it fired right up. i am thinking PMD more and more..

Quote

Top

Bottom

fozsey

Posts: 23
Joined: Sep 2003

Monday September 20, 2004 08:59
Thats a good thing. A couple hundred compared to a "C" note is always a good thing, right? Unfortunatelly the PMD's made today aren't any better than they were in 1994. They will not tolorate heat and as an electronic component I still can't understand why GM put them where they did anyway. Poor engineering.

Quote

Top

Bottom

[ CATEGORY LISTINGS : THREADS ]

Customer Testimonials

'You have been very encouraging to me in listing my inheritance of Detroit parts. THANK YOU. Things are moving, inquiries are picking up. My bills are getting paid. Just wanted to thank you.'

Devorah, NY, USA

'I was amazed to find the engine I needed in minutes! Even more amazingly, it was less than half the estimated repair cost of the original unit!'

Paul Crane, Crane Engineering, UK

'I did receive quite a few calls from the add - thanks for the service.'

Bill Aldridge, Environmental Rainwater Solutions, Wilmington, USA

hot restart for 6.5td

Customer Testimonials

Newsletter