CATEGORY LISTINGS > INTERNATIONAL

Replying to Thread:

dt466E no oil pressure while cranking

Created On Thursday 18, February, 2010 5:15 PM by shanedotson

Please enter your login information to post.
Username:
Password:
I want to stay logged in.

Message Title:

Message Text:

http

https

ftp

mail

hr

highlight

LI Quote

HTML code is permitted. Special symbols permit some HTML functionality.

shanedotson

Posts: 2
Joined: Feb 2010

Thursday February 18, 2010 17:15

2000 international 4700 flatbed tow truck. I was having trouble on cold start it would sometimes not build oil pressure fast enough and the oil/water light on the dash would come on, I would shut it off and re-start it all would be fine. Then i came in and started it and it ran about about ten seconds and died, never has re-started. I have no oil pressure while cranking. I removed oil pick up tube and inspected, found no visible cracks. I replaced IPR valve, high pressure oil pump, and main engine oil pump behind ballancer.

-------------------------
shanedotson

Quote

Top

Bottom

shanedotson

Posts: 2
Joined: Feb 2010

Friday February 19, 2010 09:11
I still have no oil pressure while cranking. I seen a guy say on another post in here something about replacing oil pump and front cover. Does something go wrong in the front cover to cause no oil pressure? ------------------------- shanedotson

Quote

Top

Bottom

trashman

Posts: 2
Joined: Mar 2010

Saturday March 13, 2010 15:54
there is a oil pressure regulator in the back front cover

Quote

Top

Bottom

DieselSmellsLikePower

Posts: 10
Joined: Aug 2009

Tuesday October 05, 2010 08:00
If the back half of the front cover (behind the oil pump) is sratched or even looks worn. you can still have no oil psi with a new pump.

Quote

Top

Bottom

alexisrois

Posts: 26
Joined: Feb 2012

Sunday September 16, 2012 21:52
When this occurs did you inspect at the throttle sensor if there is a five volts, now if there is five volts at the throttle electrical connector replace the sensor, but if there is no five volt at the electrical connector install a overlay harness. ------------------------- Fire Pump Systems provide a wide range of fire pump from Ruhrpumpen

Quote

Top

Bottom

Skidd88

Posts: 7
Joined: Feb 2014

Saturday February 15, 2014 16:39

Hey guy's! Here are a few things to look at if you have no oil pressure during cranking at start up. 1st you have to have base engine oil pressure to get the engine to start. 2nd you can pull the oil temp sensor out on the left side of the rear section of the front cover(2 wire white sensor) the oil level should be up and flow out the sensor hole. If there is no oil in this area this means that the HP oil pump has no oil to fire the engine. If this the case the oil regulator that is located behind the oil filter housing is stuck open and you will not build any oil pressure, which will cause a no start issue. 3rd if there is oil in the sensor location, then you have a bad oil pump, which is located behind the front harmonic balancer. If you attempt the repair you will need to heat up the center of the harmonic balance(the shaft hole) to get to slide the balancer back on. I hope all this info helps!

-------------------------
Master ASE Tech, International Dealership Certified, Cummins, Detroit, Freightliner Dealership Trained.

Quote

Top

Bottom

RageT

Posts: 1
Joined: Mar 2016

Sunday March 13, 2016 08:26

Hey Skidd88, I've the same problem with my 97' International 4900 DT466E. No oil pressure while cranking. This only occurs after the truck sits overnight. I removed the oil filter housing and looked at the regulator. Just to be clear, the regulator is IN the housing correct? How do I tell if it is possibly stuck open? I'm afraid my problem may be the oil pump, and or pressure relief valve, from all I've read of other issues people are having. I pulled the temp sensor and didn't have oil running out. By your post I figured it would be the regulator at the filter. Now I'm uncertain. Any insight would be great.

-------------------------
97' International DT466E 20T crane truck

Quote

Top

Bottom

[ CATEGORY LISTINGS : THREADS ]

SELECT Advert_Number, Size_Type, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type = 2 ORDER BY Advert_Number

SELECT Imps_Available FROM Advert_Imp WHERE Advert_Number = UPDATE Advert_Imp SET Imps_Available = #Imps_Available1# WHERE Advert_Number = SELECT Impressions FROM Advert_Imp_Trans WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# UPDATE Advert_Imp_Trans SET Impressions = #Impressions1# WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# INSERT INTO Advert_Imp_Trans (Advert_Number, Date, Impressions, Clicks) VALUES (#Advert_Number#, #CurrentNow#, 1, 0)

SELECT Advert_Number, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type=1 ORDER BY NEWID()

Customer Testimonials

'DieselEngineTrader.com is a very good resource. I use it to search for engines I need and have also advertised a Volvo Penta engine and received some genuine inquiries. Our local market is small and DieselEngineTrader.com helps me to reach a worldwide market.'

Dimitris Constantinou, Limassol, Cyprus

'I did receive quite a few calls from the add - thanks for the service.'

Bill Aldridge, Environmental Rainwater Solutions, Wilmington, USA

'Congratulations on your increasing traffic at web page. I keep several address slips I've made up for your web page and have had occasion to hand out 25-30 to persons needing an engine or having one to sell.'

Cal Harvey, Triangle Agriculture

dt466E no oil pressure while cranking

Customer Testimonials

Newsletter