Replying to Thread:

Injector flow chart series 60

Created On Thursday 12, December, 2013 6:47 AM by tenspeedover

Please enter your login information to post.
Username:
Password:
I want to stay logged in.

Message Title:

Message Text:

http

https

ftp

mail

hr

highlight

LI Quote

HTML code is permitted. Special symbols permit some HTML functionality.

tenspeedover

Posts: 43
Joined: Nov 2011

Thursday December 12, 2013 06:47
I have been all over the Internet and cannot find a flow chart in cc's for detroits. If anybody has any ideas please let me know. Thanks

Quote

Top

Bottom

stump

Posts: 814
Joined: Aug 2007

Friday December 13, 2013 03:49
What do you want to know? What year engine are you wanting info on.

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Friday December 13, 2013 07:10

I am curious about ddec v n3, plus ddec 3 and 4,I already have 5915 in a ddec 3 just wanting a chart for comparison maybe get a little more power, sacrifice some fuel mileage . Don't need to go huge like "825" injectors looking for something in between. The ddec v stuff I haven't heard anybody talking about changeing injectors or cams in I have a couple of ddec V motors to experiment with just need to be pointed in the right direction for part numbers or injector flow.

Quote

Top

Bottom

stump

Posts: 814
Joined: Aug 2007

Friday December 13, 2013 15:19
I don't know anything about the N3 injectors, I kind of figured out the earlier ones 5915,7014 etc.

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Saturday December 21, 2013 12:16

Thanks for the reply, I have read some of your other post on here it seems like you are running a ddec 3 I was wondering if that was true if you have piston squirters. I'm running a 526 cam and 5915 injectors in a non piston cooler block , I didn't see much power difference going from a stock 500 cam to the 526 cam I was thinking of running a 825 cam not sure about part number for it, don't know of anybody running one maybe they could weigh in on this, should I go with bigger cam or bigger injectors, I would like to hear what some other ddec 3 owners are running . Thanks

Quote

Top

Bottom

grampa

Posts: 129
Joined: Sep 2010

Saturday December 21, 2013 13:31

apparently i haven't said this enough COMBINATION COMBINATION COMBINATION,,,,,,,,,,,,,,,,,,,,,,,,,cam,injectors,turbo,and most important ECM program,,cast pistons no coolers i would stop at around 600 hp,your motor your call....is this a toy or daily driver,my daily driver ddec4, steel pistons piston coolers,.005 liner protrusion,and i mean .005 not .006,not.004.....526 cam,177287 BW turbo,7473 injectors cut back to 80% fuel in ecm.800 HP on the ground every day..yes i build my own motors pretty much have to so you know actual clearances..around 2000 HP in play mode short distance,sled pulling ,drag racing...i have found you can have as much HP as you can afford.i found my limit...5915=170 cc....7014=185cc.....7315=205cc....7473=215cc....825 cam 23529008......remember the injectors are manipulated in the program as well as every other aspect of how your engine performs and fuel mileage...remember the program,parts will help ,but remember those three words above....................................

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Saturday December 21, 2013 14:21

Thanks grandpa, that's what I wanted to know on the injector cc's, yes it's a daily driver no I don't want to go overboard 7473 s just wanted a step up from 5915 or possible cam swap from the 526. Current set up is 5915, 526 cam , 171702 and manifold and a .15 over 500 ECM done by Erich . The motor already had 5915 injectors maybe that's why I didn't see a big difference in changing to a 526 cam the truck doesn't seem to pull any better with it, didn't know if I would have more torque (under the curve) with a 825 cam. I need it to stay together no doubt about that but that being said I do my own motor work including rebuilds and actually pay attention to my gauges . If you think that I'm at my limit for ddec 3 then I will leave it alone , like I said I'm not trying to go crazy bigger just a little better ie; if I need to change injectors under normal service should just replace with 5915 or for the same price 7014 or better . I don't mind spending money but when I do I like upgrade . Thank you

Quote

Top

Bottom

loweredd

Posts: 107
Joined: Jan 2009

Monday January 13, 2014 15:52
I had been running 825/850 whatever number you use, injectors for about 5 years. I stuck in the same camshaft when I overhauled the engine. 485 +15% ecm. I just recently switched to 7014s. The powerband with this camshaft is high. It does not like it under 1600-1700 rpm.

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Thursday March 06, 2014 09:52

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Thursday March 06, 2014 09:59
Lowerred are you running a ddec 3 without piston sprayers? If so did you have any problems with your setup, like excessive heat or burnt piston?

Quote

Top

Bottom

loweredd

Posts: 107
Joined: Jan 2009

Thursday March 06, 2014 10:00
DDEC3, no coolers. It would get hot if I let it, but I didn't let it. It probably could have gone to 1600deg if it would have lived. Edited: Thursday March 06, 2014 at 10:02 by loweredd

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Thursday March 06, 2014 15:17
Lowered thanks for the reply, how does your truck run with 7014 compared to the 7473 was there a huge loss of power or does it pull the same?

Quote

Top

Bottom

loweredd

Posts: 107
Joined: Jan 2009

Thursday March 06, 2014 15:21
HUGE difference. It's not stock at all, but it seems like it. LOL. I think if I go with a 500 cam and the 177287 turno, it will wake it up. This cam is huge now, and this Michigan turbo is huge too.

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Friday March 07, 2014 11:03
I felt my truck pulled better with the stock 500 cam compared to the 526 cam, maybe I'm not driving it right. Why did you switch from the 7473 was it to much? I would like more out of it , I was thinking the 825 cam would be good for my set up but maybe I should go with bigger injectors

Quote

Top

Bottom

loweredd

Posts: 107
Joined: Jan 2009

Friday March 07, 2014 11:08
They were getting worn out and I thought the 7014s would still be fine. I wish I would have just put the same back in.

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Wednesday March 12, 2014 10:33
Lowerred do you need a 500 cam? If so I have one there is no rust and it is not flaking, it's the cam the came out of my motor when i switched the 526 cam. Not sure about the number on it but I can check on it in a couple days.

Quote

Top

Bottom

benjamin2606

Posts: 49
Joined: Apr 2014

Saturday May 03, 2014 23:29
I've got 14L pre EGR with 6995 injectors. Does anyone know the flow rating on them? ------------------------- 2000 Western Star 4964 14L 550 S60 2003 Western Star 4900EX 12.7 500 S60

Quote

Top

Bottom

stump

Posts: 814
Joined: Aug 2007

Sunday May 04, 2014 06:53
tenspeed over I might be interested in your cam what P/N is it?

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Monday May 19, 2014 18:37
Hey stump sorry about taking so long to reply I haven't been checking this thread I thought it kind of died off, I will give you the numbers tomorrow the cam is in my shop. It is a stock ddec3 and early ddec4 500 premium motor camshaft, it uses the 18mm bolt enstead of the 20 mm bolt used in most ddec4's .

Quote

Top

Bottom

tenspeedover

Posts: 43
Joined: Nov 2011

Saturday May 24, 2014 06:21
Stump that cam number is 23531680. Let me know if your interested.

Quote

Top

Bottom

[ CATEGORY LISTINGS : THREADS ]

SELECT Advert_Number, Size_Type, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type = 2 ORDER BY Advert_Number

SELECT Imps_Available FROM Advert_Imp WHERE Advert_Number = UPDATE Advert_Imp SET Imps_Available = #Imps_Available1# WHERE Advert_Number = SELECT Impressions FROM Advert_Imp_Trans WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# UPDATE Advert_Imp_Trans SET Impressions = #Impressions1# WHERE Advert_Number = AND Month(Date)=#CurrentMonth# AND Year(Date)=#CurrentYear# INSERT INTO Advert_Imp_Trans (Advert_Number, Date, Impressions, Clicks) VALUES (#Advert_Number#, #CurrentNow#, 1, 0)

SELECT Advert_Number, Banner_Name, FName, LName, CompanyName FROM Advert_Imp a LEFT OUTER JOIN Seller s ON a.Company_ID = s.SellerID WHERE Show_Advert=1 AND Size_Type=1 ORDER BY NEWID()

Customer Testimonials

'Listed a few engines to see the response and we're getting calls every other day!'

Richard Bemsee, Live Oak Diesel, Florida, USA

'I had hundreds of "hits" on your website which generated 5 or 6 inquiries from all over the world; Germany, The Philippines, Korea, Sweden, and Spain. I sold all 3 of my engines to a buyer from South Korea. Your website was invaluable to me in selling these engines; no other ads that I ran produced any inquiries.'

Gary Sommerfeld, Manager, Marine Operations, Phillips Cruises & Tours, Anchorage, Alaska

'The engine was on other sites, but we received the most calls from DieselEngineTrader.com. We sold it to the first caller-from DieselEngineTrader.com. Also, there was a waiting list on the engine if the first sale fell through! Thanks for the great service!'

Fran Trapp, South Carolina, USA

Injector flow chart series 60

Customer Testimonials

Newsletter