DieselTalk

DieselEngineTrader's FREE Diesel Engine Forums

new topic search Categories login View Kubota Engines

CATEGORY LISTINGS > KUBOTA > Kubota D950 vs Universal M25XP... timing (valves & fuel) [ REFRESH ]
Thread Title:

Kubota D950 vs Universal M25XP... timing (valves & fuel)


Created On Monday April 13, 2009 12:34 Diesel Talk
Diesel Talk Forum

Bigboat69
Diesel Talk Forum
Posts: 1
Joined: Apr 2009

Note Monday April 13, 2009 12:34 View thread in raw text format
Diesel Talk
Hello. I have a good running D950 tractor motor and a seized Universal M25XP. From what I understand, these engines are basically the same with the D950 being the core of the M25XP. Everything from the bad Uni has largely just bolted onto the good Kubota. Where I'm running into a problem is the valves and fuel injection timing. From having worked on Universal motors before (and confirming this with my Universal manual) the valve clearances should be set at compression TDC cold at .007 and fuel injection should be timed at 25 degrees before TDC.

When I started, I noticed a few odd things when compared to what I'm used to. 1) The "1TC" marking on the flywheel is actually 3TDC. (Everything I know about Universals is that #1 is always the one closed to the V-belt). 2) The fuel injection seems to be timed to come at right at TDC not 25 degrees before! 3) the clearances before I started were .014 exhaust and .000 intake. (This is also the maximum gap at any point of rotating the engine.)

So basically my questions are these:

1) Where is the timing mark on a Kubota D950 ( or D850 or D750 which all same stroke)? It seems that there's a raised tip about the size of a pencil eraser at 11 o'clock that when lined up with the 1TC mark on the flywheel gets cylinder #3 in TDC
2) Is it really possible that Kubota number's the cylinders different that Universal? Both engines turn the same way (counter clockwise when facing the flywheel) but the Uni goes 3-2-1 and the Kubota goes 1-2-3.
3) What is involved with adjusting the fuel cam shaft's rotation? So far I've replaced starters, alternators and heads on this engine... never a full tear down. From what I see here: Marine Diesel Direct -- Universal M25XP Fuel Cam Group it looks somewhat straight forward... once I get down to it, I remove the Circlip and then the pump gear, rotate the cam and then put everything back together. Keeping those ball bearing in place behind the gear might be challenging though!

PS For those that are wondering, I understand the whole concept of "rocking the rockers" until they're at their most open / watching the valve open and close to confirm which is exhaust and which is intake. I literally just did a valve adjustment on a universal 5411 / Z500 last week. Dealing with this last stretch of this engine, I feel like I'm the one who didn't take my crazy pill.
PPS The Kubota ran with the valves in those settings but coughed a little black smoke when I gave some throttle. Fuel good, air intake clear, exhaust not blocked, injectors check out fine. I figured I'd set the valves and then spray some SeaFoam through the air intake to clear the black smoke.

On a side note, it seems that every D950 or similar I see running on YouTube belches a little exhaust with throttle. Thoughts?
Diesel Talk Forum
Reply Diesel Talk Forum Quote Diesel Talk Top Diesel Talk Forum Bottom Diesel Talk
Diesel Talk Forum
Diesel Talk Forum

m4ttj00
Diesel Talk Forum
Posts: 1
Joined: Jul 2015

Note Friday July 10, 2015 14:02 View thread in raw text format
Diesel Talk
I know this post is really old, but did you ever get this sorted?

I'm about to buy a d950 and perform the same swap.
Diesel Talk Forum
Reply Diesel Talk Forum Quote Diesel Talk Top Diesel Talk Forum Bottom Diesel Talk
Diesel Talk Forum
CATEGORY LISTINGS > KUBOTA [ REFRESH ]
Adelman's Truck Parts Corp.
Adelman's Truck Parts Corp.
Duncan Rogers (Engineering) Ltd
Big Bear Engine Company
Duncan Rogers (Engineering) Ltd
Advertize on Diesel Engine Trader

Customer Testimonials

Newsletter

Subscribe to our mailing list to get all the latest DET news.as well as daily or weekly notifications of new engines, gensets and spare parts listings.

'I had a Cummins ISX600 sitting in my shop for 2 years and finally managed to sell it through DieselEngineTrader.com! Great service and I like the way that the Buyer was able to phone me directly.'

David G Bouchard, Los Angeles, USA

'It took at least 4 weeks before we got our first inquiries for the 28 engines we listed - 3 months on we are making 3 to 4 sales per month! We're really pleased and I like the feature that shows how many views our engines get.'

Pete Melhuish, Northwest Diesel Parts, Portland, Oregon, USA

'We're thrilled with DieselEngineTrader.com! We sold an old CAT D343 within 1 month of listing and a Cummins engine within 3 months. We were amazed - we didn't think anyone would want them in the condition they were in!'

Stephanie Vaughan, Heavy Equipment Parts, Independence, USA

Copyright Diesel Engine Trader 2015